NAME

    Algorithm::Backoff::RetryTimeouts - A backoff-style retry algorithm
    with adjustable timeout support

VERSION

    version v1.0.0

SYNOPSIS

        use Algorithm::Backoff::RetryTimeouts;
    
        my $retry_algo = Algorithm::Backoff::RetryTimeouts->new(
            # common adjustments (defaults shown)
            max_attempts          => 8,
            max_actual_duration   => 50,
            jitter_factor         => 0.1,
            timeout_jitter_factor => 0.1,
            adjust_timeout_factor => 0.5,
            min_adjust_timeout    => 5,
    
            # other defaults
            initial_delay         => sqrt(2),
            exponent_base         => sqrt(2),
            delay_on_success      => 0,
            min_delay             => 0,
            max_delay             => undef,
            consider_actual_delay => 1,
        );
    
        my ($delay, $timeout);
        $timeout = $retry_algo->timeout;
    
        my $is_successful = 0;
        while (!$is_successful) {
            $actionee->timeout( $timeout );
            $is_successful = $actionee->do_the_thing;
    
            ($delay, $timeout) = $is_successful ? $retry_algo->success : $retry_algo->failure;
            die "Ran out of time" if $delay == -1;
            sleep $delay;
        }

DESCRIPTION

    This module is a subclass of Algorithm::Backoff::Exponential that adds
    support for adjustable timeouts during each retry. This also comes with
    a sane set of defaults as a good baseline for most kinds of retry
    operations.

    A combination of features solves for most problems that would arise
    from retry operations:

      * Maximum attempts - Forces the algorithm to give up if repeated
      attempts don't yield success.

      * Maximum duration - Forces the algorithm to give up if no successes
      happen within a certain time frame.

      * Exponential backoff - A sqrt(2) exponential delay keeps single
      retries from waiting too long, while spreading out repeated retries
      that may fail too quickly and run out of max attempts. This also
      decreases the congestion that happens with repeated attempts.

      * Jitter - Adding random jitter to the retry delays solves for the
      Thundering Herd problem.

      * Adjustable timeouts - Providing an adjustable timeout after each
      request solves the opposite problem of exponential backoffs: slower,
      unresponsive errors that gobble up all of the max duration time in
      one go. Each new timeout is a certain percentage of the time left.

 Typical scenario

    Here's an example scenario of the algorithm with existing defaults:

        $retry_algo is created, and timer starts
    
        Initial timeout is 25s
    
        1st attempt fails instantly
    
        $retry_algo says to wait 1.4s (±10% jitter), and use a timeout of 24.3s
    
        2nd attempt fails instantly
    
        $retry_algo says to wait 2s (±10% jitter), and use a timeout of 23.3s
    
        3rd attempt fails after the full 23.3s timeout
    
        $retry_algo says to not wait (since the attempt already used up the delay), and use
        a timeout of 11.7s
    
        4th attempt succeeds

CONSTRUCTOR

    The "new" constructor takes all of the base options from
    Algorithm::Backoff::Exponential. Some of the defaults are changed (also
    shown in the "SYNOPSIS" above), but otherwise function the same way.

      * max_attempts => uint (default: 8)

      * max_actual_duration => ufloat (default: 50)

      * jitter_factor => float (default: 0.1)

      * initial_delay => ufloat (default: sqrt(2))

      * exponent_base => ufloat (default: sqrt(2))

      * delay_on_success => ufloat (default: 0)

      * min_delay => ufloat (default: 0)

      * max_delay => ufloat

      * consider_actual_delay => bool (default: 1)

    The following new options are added in this module:

      * adjust_timeout_factor => ufloat (default: 0.5)

      How much of the remaining time to use for the next attempt's timeout,
      as a factor between 0 and 1.

      In order to prevent a single attempt from using up all of the
      remaining time, an adjustable timeout will force the attempt to only
      use a portion of the time. By default, only 50% of the remaining time
      will be set as the next timeout value.

      * min_adjust_timeout => ufloat (default: 5)

      Minimum timeout value, in seconds.

      This value bypasses any max_actual_duration checks, so the total time
      spent on sleeping and attempts may end up exceeding that value by a
      small amount (up to max_actual_duration + min_adjust_timeout). In
      this case, future failures will return a delay of -1 as expected.

      * timeout_jitter_factor => float (default: 0.1)

      How much randomness to add to the adjustable timeout.

      Delay jitter may not be enough to desynchronize two processes that
      are consistently timing out on the same problem. In those cases, the
      delay will usually be zero and won't have any sort of jitter to solve
      the problem itself. A jitter factor against the timeout will ensure
      simultaneous attempts have slightly different timeout windows.

METHODS

 success

        my ($delay, $timeout) = $retry_algo->success([ $timestamp ]);

    Log a successful attempt. If not specified, $timestamp defaults to
    current time. Unlike the base class, this method will return a list
    containing both the suggested delay and the suggested timeout for the
    next attempt.

 failure

        my ($delay, $timeout) = $retry_algo->failure([ $timestamp ]);

    Log a failed attempt. If not specified, $timestamp defaults to current
    time. Unlike the base class, this method will return a list containing
    both the suggested delay and the suggested timeout for the next
    attempt.

 delay

        my $delay = $retry_algo->delay;

    Returns the last suggested delay, in seconds.

    The delay will return -1 to suggest that the process should give up and
    fail, if max_attempts or max_actual_duration have been reached.

 timeout

        my $timeout = $retry_algo->delay;

    Returns the last suggested timeout, in seconds. If no attempts have
    been logged, it will suggest an initial timeout to start with.

    This will be a floating-point number, so you may need to convert it to
    an integer if your timeout system doesn't support decimals.

    A timeout of -1 will be returned if max_actual_duration was forcefully
    turned off.

SEE ALSO

    Algorithm::Backoff - Base distro for this module

AUTHOR

    Grant Street Group <developers@grantstreet.com>

COPYRIGHT AND LICENSE

    This software is Copyright (c) 2020 - 2021 by Grant Street Group.

    This is free software, licensed under:

      The Artistic License 2.0 (GPL Compatible)